VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
- 8. Running gear
   - 8.1.2. Depreciation rack
      8.1.2.1. Repair of a depreciation rack
      8.1.3. Removal and installation of a power shaft
      8.1.4. Amount of G 000 603 lubricant for external hinges of power shafts
      8.1.5. Lubricant of the internal three-humeral hinge
      8.1.6. Filling of the CV JOINT with G6 lubricant
      8.1.7. Replacement of the internal hinge of equal angular speeds
      8.1.8. Replacement of the external hinge of equal angular speeds
      8.1.9. Dismantling of the external hinge of equal angular speeds
      8.1.10. Malfunctions of power shafts
   + 8.2. Back suspension bracket
   + 8.3. Wheels and tires
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Heating, ventilation
+ 13. Electric equipment






8.1.2. Depreciation rack

GENERAL INFORMATION

Arm arrangement for fastening of a wire of the ABS sensor (shooter)

1 – fastening of the internal end of a power shaft

Elements of the top fastening of a rotary fist

1 – nut,
2 – top cross levers,
3, 4 – fastening of steering draft

Removal

PERFORMANCE ORDER
1. Weaken bolts of fastening of forward wheels, then lift a forward part of the car and fix on supports. Remove forward wheels.
2. From the water waste channel remove rubber inserts.
3. Unscrew two nuts of the top fastening of a depreciation rack, at the same time do not damage a sheeting of brake pipelines.
4. Take from an arm on a brake support an ABS sensor wire, see rice. An arm arrangement for fastening of a wire of the ABS sensor (shooter).
5. Unscrew a nut (1), take a bolt and, having pulled up, take the top cross levers (2) from a rotary fist, see rice. Elements of the top fastening of a rotary fist.
Prevention

Do not expand grooves in a rotary fist at extraction of the top cross levers. It is forbidden to unscrew bolts of fastening of steering thirst for a rotary fist, otherwise it will be necessary to adjust the angles of installation of forward wheels (3 and 4), see rice. Elements of the top fastening of a rotary fist.


6. Reject the top part of a rotary fist (shooter), see rice aside. Elements of the top fastening of a rotary fist.
7. Unscrew a nut and take a bolt of the lower fastening of a depreciation rack to the lower cross lever.
8. Being careful, take a depreciation rack from under a forward wing. At the same time do not damage a protective cover of the hinge of equal angular speeds of a power shaft.

Installation

Opening arrangement in a spring nest


1 – nut of the lower fastening of a depreciation rack,
2 – bolt of fixing of the top cross levers

PERFORMANCE ORDER
1. Establish a depreciation rack so that the opening in a nest of a spring settled down from the inside, see rice. An opening arrangement in a spring nest.
2. Install a fork of the lower fastening of a depreciation rack on the cross lever and fix by a bolt and a nut, having tightened their moment 90 Nanometers.
3. Install the top cross levers against the stop in a rotary fist and fix them by a bolt and a nut, having tightened their moment 40 Nanometers (2), see rice. An opening arrangement in a spring nest.
4. Fix an ABS sensor wire on a brake support arm.
5. Fix the top part of a depreciation rack by nuts, having tightened their moment 20 Nanometers, but at the same time do not damage a sheeting of brake pipelines.
6. Establish rubber inserts in a gutter.
7. Apply a thin film of lubricant on a fillet of the nave aligning a wheel disk. Establish a wheel and fix it by bolts. Lower the car and tighten bolts of fastening of a wheel the moment of 120 Nanometers.