VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
- 5. Engine management
   5.2. Work of a control system of the engine
   5.3. Check of system of injection of fuel
   5.4. Sensors and executive mechanisms of a control system of the engine
   - 5.5. System of ignition
      5.5.1. System of direct ignition (except engines 1,6-I ADP)
      5.5.2. System of ignition with the distributor of ignition (engine 1,6-I ADP)
      5.5.2.1. Ignition distributor
   + 5.6. Fuel highway and fuel nozzles
   5.7. Main malfunctions of a control system of the engine
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Heating, ventilation
+ 13. Electric equipment






5.5.2.1. Ignition distributor

GENERAL INFORMATION

The distributor of ignition has Hall's sensor.

Removal

PERFORMANCE ORDER
1. Turn a bent shaft of the engine in such situation at which the piston of the first cylinder will be in VMT in a compression step.
2. Uncover the ignition distributor for what previously the screw-driver release the fixing bracket.
3. Disconnect the electric socket from Hall's sensor.
4. Unscrew a fastening bolt in the basis of the distributor of ignition and remove the ignition distributor.
Prevention

At the removed distributor of ignition do not turn a bent shaft of the engine.



Installation

PERFORMANCE ORDER
1. Before installation of the distributor of ignition check that the bent shaft of the engine is established in such situation at which the piston of the first cylinder is in VMT in a compression step. At the same time adjusting tags on pulleys of cranked and distributive shaft have to be combined with indexes.
2. Check a state and correctness of installation of a sealing ring of the distributor of ignition. If necessary replace a sealing ring.
3. If the bent shaft of the engine was turned at the removed ignition distributor, then turn it further to such situation when the axis of fastening of a flange of the distributor of ignition is not established on one line with a carving opening.
4. Turn an ignition distributor rotor so that the central part of an electrode of a rotor was combined with a groove on the ignition distributor case. From this situation turn a rotor slightly clockwise and install the ignition distributor. At installation distribute la of ignition the rotor of the distributor has to turn in a starting position and the central part of an electrode of a rotor has to be combined with a groove on the ignition distributor case. Fix the ignition distributor by a bolt, having tightened its moment 25 Nanometers.
5. Check a condition of a cover of the distributor of ignition for existence of corrosion of contacts, black paths between contacts, and also integrity and smoothness of movement of coal contact in the center of a cover. With defects replace an ignition distributor cover.
6. Also check a state and fastening of metal contact of a rotor of the distributor. If the contact burned or its fastening weakened, replace a distributor rotor. In the presence remove a deposit and traces of corrosion from contact, using a small file.
7. Establish a cover of the distributor of ignition and fix it by the fixing bracket.
8. If in a cover of the distributor of ignition high-voltage wires were removed, connect them to a cover in the sequence of operation of cylinders of the engine 1-3-4-2. The electrode for connection of a high-voltage wire of the first cylinder is located about mark VMT in the ignition distributor case. Further connection of wires is made clockwise.
9. Connect the electric socket to Hall's sensor.
10. After replacement of the distributor of ignition address in a specialized workshop for a call from memory of the control unit the engine of the written-down malfunctions and their deletings.