Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Heating, ventilation
- 13. Electric equipment
13.2. General information
+ 13.3. Electric chains
13.4. Safety locks
13.5. Rules of care of the accumulator
13.6. Check of the accumulator
13.7. Accumulator charging
13.9. System of charging
13:11. Replacement of brushes of the generator and regulator of tension
13:12. System of start of the engine
13:14. Traction relay of a starter
13:15. Replacement of bulbs of external lighting
13:16. Replacement of bulbs of internal lighting
13:17. Devices of external lighting
13:18. Executive engine of the proofreader of light of headlights
13:19. Adjustment of light of headlights
13:20. Gas-discharge lamps of headlights of passing beam
13:21. Combination of devices
13:22. Multipurpose switches of a steering column
13:24. Radio receiver
13:25. High-frequency loudspeakers
13:26. Low-frequency loudspeakers
13:28. Check of a heater of back glass
13:29. Windshield screen wiper engine
13:30. Engine of a screen wiper of back glass
13:31. Windscreen washer pump
13:32. System of the central blocking of locks
13:33. Main malfunctions of the generator
13:34. Main malfunctions of a starter
+ 13:35. Electric circuits
Interpretation of the symbols applied on the label of the accumulator
| 1 – At service of the accumulator it is necessary to follow the rules according to safety measures stated in the operation manual.
2 – In the accumulator there is a corroding acid and it is necessary to be careful that acid did not spill from the accumulator.
3 – Do not use naked flame about the accumulator.
4 – During the work with the accumulator use goggles.
|5 – You keep the accumulator in the place not available to children.
6 – At utilization hand over the accumulator only in points intended for this purpose.
7 – Do not throw out the accumulator together with household garbage.
8 – The gases emitted at accumulator charging are explosive.
Connection of a hose for a conclusion of the gases from the accumulator which are formed during its work
Elements of fastening of the accumulator
||1 – basic arm,
2 – fixing plate,
3 – bolt,
4 – arm
The accumulator is installed in a back part of a motor compartment at the windshield basis.
At a detachment of plugs of the accumulator in blocks of memory of control units data on the written-down malfunctions therefore before a detachment of plugs of the accumulator it is desirable to address in a specialized workshop for a call from memory of the malfunctions which are written down in it are erased. After connection of the plug of the accumulator it is necessary to make active and reprogram window regulators with the electric drive, and also the provision of rear-view mirrors and seats.
Also if the radio receiver with a code is installed in the car, then before a detachment of plugs from the accumulator, check that you have a code for repeated activization of the receiver. Otherwise it will be possible to put the radio receiver into operation only at the specialized station Volkswagen.
At installation of the new accumulator it is necessary to use only the accumulator with a conclusion of the gases which are formed during the operation of the accumulator see rice. Connection of a hose for a conclusion of the gases from the accumulator which are formed during its work.
| PERFORMANCE ORDER
| 1. Switch off ignition.
| 2. Open a cowl.
||3. Remove the negative plug from the accumulator and move it aside.
|4. Remove a protective cover, weaken fastening and remove the positive plug from the accumulator.
||5. In the lower part of the accumulator unscrew a bolt and remove a plate of fastening of the accumulator.
|6. Move the accumulator aside, at the same time fastening of the second party of the accumulator will be released, and take the accumulator from a motor compartment.
|7. On the accumulator there is a sticker with the warning symbols, see rice. Interpretation of the symbols applied on the label of the accumulator.
At installation аккумулято ра do not press a hose, it is intended ny for removal of the gases which are emitted during the operation of the accumulator. In the pipeline of removal of gases there is a valve which protects the accumulator from a backfire.
| PERFORMANCE ORDER
| 1. Establish one party of the accumulator on a basic arm, see rice. Elements of fastening of the accumulator.
| 2. From the second party fix the accumulator and screw it a bolt, having tightened its moment 20 Nanometers.
| 3. Check reliability of fastening of the accumulator, otherwise service life of the accumulator can be considerable is reduced.
|4. Connect to the accumulator at first the positive plug, and then negative and fix them, having tightened fastening nuts the moment of 5 Nanometers.
|5. If the radio receiver with a code is installed in the car, repeatedly reprogram it.
|6. Determine time on hours.
|7. Make active window regulators with the electric drive.
|7a. Close outside the car through a door of the driver or a door of the forward passenger. Check that glasses and doors were reliably closed.
|7b. Repeatedly close the car a key, at the same time hold a key in a closed position at least one second.
If there is a defect electric a window regulator, then illumination of buttons of management on a door will blink.
|8. Intensify function of storing of provisions of external rear-view mirrors and seats.
|8a. Open the driver's door.
|8b. Include ignition.
|8 century. Move with buttons of management sitting of the driver forward and up to an emphasis.
|8 g. Buttons of management incline a back of sitting of the driver against the stop forward.
|8. Switch off ignition.