Foltsvagen Passat B5 + Maintenance instruction + 1. Maintenance + 2. Engines + 3. Cooling system + 4. Fuel system + 5. Engine management + 6. Exhaust system + 7. Transmission + 8. Running gear + 9. Steering + 10. Brake system + 11. Body + 12. Heating, ventilation - 13. Electric equipment 13.2. General information + 13.3. Electric chains 13.4. Safety locks 13.5. Rules of care of the accumulator 13.6. Check of the accumulator 13.7. Accumulator charging 13.8. Accumulator 13.9. System of charging 13:10. Generator 13:11. Replacement of brushes of the generator and regulator of tension 13:12. System of start of the engine 13:13. Starter 13:14. Traction relay of a starter 13:15. Replacement of bulbs of external lighting 13:16. Replacement of bulbs of internal lighting 13:17. Devices of external lighting 13:18. Executive engine of the proofreader of light of headlights 13:19. Adjustment of light of headlights 13:20. Gas-discharge lamps of headlights of passing beam 13:21. Combination of devices 13:22. Multipurpose switches of a steering column 13:23. Switches 13:24. Radio receiver 13:25. High-frequency loudspeakers 13:26. Low-frequency loudspeakers 13:27. Antenna 13:28. Check of a heater of back glass 13:29. Windshield screen wiper engine 13:30. Engine of a screen wiper of back glass 13:31. Windscreen washer pump 13:32. System of the central blocking of locks 13:33. Main malfunctions of the generator 13:34. Main malfunctions of a starter + 13:35. Electric circuits
|
Windshield screen wiper
1 – bolt, 2 – drafts, 3 – nut, 4 – crank, 5 – screen wiper brush, |
6 – screen wiper lever, 7 – cap, 8 – nut, 9 – engine, 10 – arm |
Screen wiper mechanism drive elements
1 – drafts of a screen wiper, 2 – engine crank, 3 – bolts of fastening of the engine of a screen wiper |
|
Removal
PERFORMANCE ORDER |
1. Switch off ignition and remove a weight wire from the accumulator. |
2. Remove levers of screen wipers. |
3. Remove an air inlet lattice. |
|
4. Unscrew screws and uncover the electronic block under a windshield. |
|
5. Unscrew the nut located in the electronic block. |
|
6. Unscrew the nut located sideways the electronic block, raise the block from rubber laying and move it forward. |
7. Disconnect the multicontact electric socket from the engine of screen wipers. |
|
8. Unscrew three bolts fixing the mechanism of screen wipers to a body of the car and remove the mechanism of screen wipers from the car. |
9. Remove drafts of screen wipers from an engine crank, see rice. Screen wiper mechanism drive elements. |
10. Unscrew a nut of fastening of a crank to an electric motor shaft, at the same time hold a crank from a provorachivaniye. Moving a crank to the parties, remove it from a landing cone of a shaft of the electric motor. |
11. Unscrew three bolts and remove the engine from an arm of screen wipers. |
|
Installation
Crank with drafts of a screen wiper
PERFORMANCE ORDER |
1. At installation of the new engine of a screen wiper establish it in a starting position. For this purpose connect the multicontact electric socket to the screen wiper engine and connect a weight wire to the accumulator. Switch on and off an operating mode of screen wipers, at the same time the engine of a screen wiper will be installed in a starting position. Remove a weight wire from the accumulator and disconnect the electric socket from the screen wiper electric motor. |
2. Install the electric motor on the mechanism of screen wipers and fix by bolts, having tightened their moment 10 Nanometers. |
3. Establish on an electric motor shaft a crank in such situation that it was on one line with drafts of a stekloocha of stitel (see rice. A crank with drafts of a screen wiper). Tighten a nut of fastening of a crank the moment of 20 Nanometers. |
4. Fix on a crank of draft of screen wipers. |
5. Insert the mechanism of screen wipers into the car and fix by bolts. |
6. Install the electronic block into place and fix it by a nut and a bolt. |
7. Install a cover on the electronic block and fix it by screws. |
8. Establish an air inlet lattice. |
9. Install levers of screen wipers and fix them by nuts, having tightened their moment 15 Nanometers. |
10. Connect a weight wire to the accumulator. |
11. Check work of screen wipers. |
|
|
|