Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Heating, ventilation
- 13. Electric equipment
13.2. General information
+ 13.3. Electric chains
13.4. Safety locks
13.5. Rules of care of the accumulator
13.6. Check of the accumulator
13.7. Accumulator charging
13.9. System of charging
13:11. Replacement of brushes of the generator and regulator of tension
13:12. System of start of the engine
13:14. Traction relay of a starter
13:15. Replacement of bulbs of external lighting
13:16. Replacement of bulbs of internal lighting
13:17. Devices of external lighting
13:18. Executive engine of the proofreader of light of headlights
13:19. Adjustment of light of headlights
13:20. Gas-discharge lamps of headlights of passing beam
13:21. Combination of devices
13:22. Multipurpose switches of a steering column
13:24. Radio receiver
13:25. High-frequency loudspeakers
13:26. Low-frequency loudspeakers
13:28. Check of a heater of back glass
13:29. Windshield screen wiper engine
13:30. Engine of a screen wiper of back glass
13:31. Windscreen washer pump
13:32. System of the central blocking of locks
13:33. Main malfunctions of the generator
13:34. Main malfunctions of a starter
+ 13:35. Electric circuits
Arrangement of the radio receiver and loudspeakers in the car
| 1 – high-frequency loudspeakers on forward doors,
2 – low-frequency loudspeakers on forward doors,
3 – high-frequency loudspeakers on back doors,
4 – low-frequency loudspeakers on back doors,
5 – the radio receiver on the dashboard
The radio receiver installed at the plant has a pocket thanks to which process of removal and installation of the radio receiver is facilitated. For removal of the radio receiver it is necessary to use two special keys.
The special key used for removal of the radio receiver from the car
Arrangement of narrow cracks for installation of special keys at extraction of the radio receiver
Use of special keys for extraction of the radio receiver from a nest in the dashboard
| PERFORMANCE ORDER
| 1. Switch off ignition.
| 2. Remove a weight wire from the accumulator.
At removal of a wire of weight from the accumulator contents of cells of memory of electronic control units and the radio receiver are erased.
| 3. As the standard equipment on the car the radio receiver, having the coded device against theft which is executed on the basis of the microprocessor is installed. After disconnection of the radio receiver from electric network of the car (removal of the rechargeable battery, removal of the radio receiver or initial installation of the radio receiver) it is necessary to enter a safety code. The radio receiver will be able to be switched on only after input of the correct code.
|4. Before removal of a wire of weight from the accumulator check whether you have a radio receiver code. In the absence of a code of safety it is possible to put into operation the radio receiver only at the specialized station Volkswagen. The individual code of safety of the radio receiver is available in the technical documentation enclosed to the car at sale.
|5. For removal of the radio receiver it is necessary to use two special keys 3316, see rice. The special key used for removal of the radio receiver from the car.
|6. Insert two keys into the narrow cracks located from two parties of the radio receiver before fixing of keys see rice. An arrangement of narrow cracks for installation of special keys at extraction of the radio receiver.
|7. For heads of keys take the radio receiver from a nest (see rice. Use of special keys for extraction of the radio receiver from a nest in the dashboard). At extraction do not warp the radio receiver and do not pull it aside.
|8. Remove special keys for what wring out side clamps of the radio receiver down.
|9. Disconnect from the radio receiver electric sockets of loudspeakers and the antenna, and also the multicontact socket of giving of tension to the radio receiver. If for connection not multicontact sockets are used, before a detachment of sockets mark them.
| PERFORMANCE ORDER
| 1. Connect electric sockets to a back part of the radio receiver.
| 2. Insert the radio receiver into a dashboard nest to a zashchelkivaniye of spring clamps.
| 3. Connect a weight wire to the accumulator.
4. After installation of the radio receiver enter a safety code. On radio receivers with a safety code on a forward key there is a red emblem in the form of a key. The individual code of safety of the radio receiver is available in the technical documentation enclosed to the car at sale. You store record of an individual code in the safe place and never you keep it in the car.
|5. Enter a code of safety of the radio receiver as follows.
|6. Turn on the radio receiver.
|7. At the same time press the TR and TA keys before emergence of indication 1000, then release keys.
|8. Enter a safety code, using keys of the choice of stations with 1 on 4. The key 1 defines the first number of a code, a key 2 – the second number of a code etc.
|9. Again at the same time press the TR and TA keys before emergence of indication of SAVE, then release keys. Now the receiver is put into operation, and on the display the frequency of the accepted radio station is highlighted. If the code of safety was correctly entered into the radio receiver, then after extraction of a key from the lock of ignition the light-emitting diode close to an inscription of the name of the radio receiver has to blink.
If the safety code was incorrectly entered into the radio receiver, the inscription SAVE at first will start blinking, and then will light up constantly. After that it is possible to repeat process of input of a code of safety only once. At repeated wrong input of a code of safety the radio receiver will be blocked and within an hour it cannot be put into operation. In an hour during which the radio receiver has to be switched on, repeat input of a code of safety.