VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Heating, ventilation
- 13. Electric equipment
   13.2. General information
   + 13.3. Electric chains
   13.4. Safety locks
   13.5. Rules of care of the accumulator
   13.6. Check of the accumulator
   13.7. Accumulator charging
   13.8. Accumulator
   13.9. System of charging
   13:10. Generator
   13:11. Replacement of brushes of the generator and regulator of tension
   13:12. System of start of the engine
   13:13. Starter
   13:14. Traction relay of a starter
   13:15. Replacement of bulbs of external lighting
   13:16. Replacement of bulbs of internal lighting
   13:17. Devices of external lighting
   13:18. Executive engine of the proofreader of light of headlights
   13:19. Adjustment of light of headlights
   13:20. Gas-discharge lamps of headlights of passing beam
   13:21. Combination of devices
   13:22. Multipurpose switches of a steering column
   13:23. Switches
   13:24. Radio receiver
   13:25. High-frequency loudspeakers
   13:26. Low-frequency loudspeakers
   13:27. Antenna
   13:28. Check of a heater of back glass
   13:29. Windshield screen wiper engine
   13:30. Engine of a screen wiper of back glass
   13:31. Windscreen washer pump
   13:32. System of the central blocking of locks
   13:33. Main malfunctions of the generator
   13:34. Main malfunctions of a starter
   + 13:35. Electric circuits






13:17. Devices of external lighting

GENERAL INFORMATION

Knot of adjustment of gaps on headlight perimeter

1 – cap,
2 – screw of fastening of a headlight,
3 – adjusting carving plug,
4 – at the main adjustment the size is equal 3,5 ± 2,5 mm

Headlight

PERFORMANCE ORDER
1. The headlight case not folding and with defects the case of a headlight needs to be replaced assembled.
2. Remove the forward index of turns.
3. Not to damage a paint and varnish covering at removal of a headlight, tape details under a headlight (V) and from a front grille (And).
4. Disconnect electric sockets from a headlight.
5. Disconnect the electric socket from the electric motor of the proofreader of light of headlights.
6. Using a screw-driver edge, remove the caps closing the top bolts of fastening of a headlight.
7. Unscrew three bolts of fastening of a headlight.
8. Move a headlight to the outer side of the car.
9. Having pulled forward, remove a headlight from the car. If necessary wring out a headlight clamp from a front grille.
10. Being careful, establish a headlight in a nest in a forward part of a body. If necessary wring out a headlight clamp from a front grille.
11. Move a headlight to the center of the car.
12. Screw in and is insignificant, the moment of 3,5 Nanometers, tighten screws of fastening of a headlight.
13. Check uniformity of gaps on perimeter of a headlight and, if necessary, adjust the provision of a headlight.
14. For adjustment of provision of a headlight weaken three bolts of fastening of a headlight so that the headlight could be moved.
15. You make adjustment of gaps, screwing in or unscrewing the adjusting plug (3) a wrench on 17 mm, see rice. Knot of adjustment of gaps on headlight perimeter.
16. Tighten screws of fastening of a headlight the moment of 3,5 Nanometers and check gaps on headlight perimeter.
17. Close the top screws of fastening of a headlight caps.
18. Connect electric sockets to a headlight.
19. Establish into place the forward index of turns.
20. Check and, if necessary adjust light of headlights.

Forward index of turns

Arrangement of the lock ledges of the forward index of turns directing (arrows) on a headlight for installation

1 – electric socket of the forward index of turns

The place of fastening of the forward index of turns by the sprung loop

 

Prevention

Before removal of the right forward index of turns remove an air inlet.


PERFORMANCE ORDER
1. Pull the sprung loop fixed on the case of the index of turns to its detachment see rice back. The place of fastening of the forward index of turns by the sprung loop.
2. Having pulled forward, remove the forward index of turns from the car.
3. Disconnect the electric socket of the forward index of turns.
4. If necessary replace a bulb of the forward index of turns.
5. Connect the electric socket of the forward index of turns, see rice. An arrangement of the lock ledges of the forward index of turns directing (arrows) on a headlight for installation.
6. Insert the forward index of turns into place and against the stop move it back. Pay attention to that lock ledges which are strengthened on the case entered the directing headlights and a wing, see rice. An arrangement of the lock ledges of the forward index of turns directing (arrows) on a headlight for installation.
7. Pull the sprung loop back and fix it in the middle of the holder's flute.

Back lamp

PERFORMANCE ORDER
1. Remove the holder of lamps of a back lamp.
2. Unscrew three nuts of fastening of a back lamp and, moving it back, remove from the car.
3. Check a condition of consolidation of a back lamp and, in the presence of damages, replace it.
4. Insert a back lamp into place and fix it by nuts, having tightened their moment 3 Nanometers.
5. Establish the holder of lamps of a back lamp.