VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
   + 11.6. Forward cross panel
   11.7. Front bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of the side directing bumper arm
   11:10. Rear bumper
   11:11. Forward wing
   11:12. Facing of a niche of a forward wheel
   11:13. Air inlet lattice
   + 11:14. Cowl
   11:15. Front grille
   + 11:16. Cable of opening of the lock of a cowl
   11:17. Cowl lock
   11:18. Internal finishing of a door
   11:19. Differences at removal of an upholstery of the right forward door
   11:20. Control unit of door mechanisms
   11:21. Consolidation of a door
   11:22. Side finishing of the luggage compartment of the Sedan models
   11:23. Side finishing of the luggage compartment of the Station wagon models
   11:24. Back finishing of the luggage compartment on the Sedan models
   11:25. Trunk lid upholstery
   11:26. Luggage carrier door upholstery
   11:27. A covering of half of the luggage compartment on the Station wagon models
   11:28. Trunk lid
   + 11:29. Luggage carrier lock
   11:30. Adjustment of provision of a cover of a luggage carrier / back door
   + 11:31. The lock of a back door on the Station wagon models
   11:32. Forward door
   11:33. Cylinder of the lock of a forward door
   11:34. External handle of opening of a door
   11:35. Door lock
   11:36. Manual lowering of glass of a door
   11:37. Door glass
   11:38. Door arm
   11:39. Internal rear-view mirror
   11:40. Central console
   11:41. Forward ashtray
   11:42. Back ashtray
   11:43. Decorative overlay of the lever (automatic transmission)
   11:44. Decorative slips under the radio receiver
   11:45. The lower finishing of the dashboard from the driver
   11:46. Ware box
   11:47. Internal decorative overlay of an external rear-view mirror
   11:48. Ceiling handle
   11:49. Antisolar peaks
   11:50. Overlays of thresholds
   11:51. Wind and back flew down
   11:52. Sitting lobbies
   11:53. Head restraint
   11:54. Side safety cushions
   11:55. Back sitting
   11:56. Left back of back sitting
   11:57. Carpet
   11:58. Elements of finishing of an interior
   11:59. External mirror of a back type / glass of a mirror
   11.60. Case of an external mirror
   11.61. Protection / бордюрная roof level
   11.62. Side overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windshield
   11.65. Screen wiper levers
+ 12. Heating, ventilation
+ 13. Electric equipment






11.63. Replacement of rubber tapes of brushes of screen wipers

GENERAL INFORMATION

Regularly check overall performance of brushes of a screen wiper. Friction of brushes on the icy surface of glasses leads to damage of rubber tapes of brushes of a screen wiper. Wipe the polluted brushes of a screen wiper with soft rags and special means.

It is necessary to replace brushes at which the rubber tape hardened, cracked or became covered with silicone.

Removal

PERFORMANCE ORDER
1. Lift the brush lever to la's stekloochistita from a windshield. Turn a screen wiper brush at an angle 90 ° to the screen wiper lever.
2. Press a clamp of a brush of a stekloochista of a tel (arrow A), then move a brush on the lever (arrow B) and, moving it in the opposite direction, remove from the screen wiper lever.
3. From two parties squeeze steel amplifiers of a rubber tape of a screen wiper and take a rubber tape of a screen wiper from a brush end face.

Installation

Arrangement of dredging of a clamp on a rubber tape of a brush of a screen wiper


PERFORMANCE ORDER
1. Insert a new rubber tape without steel amplifiers into the lower clips of a brush of a screen wiper.
2. Insert steel amplifiers into the first flute of a rubber tape.
3. Squeeze Passatizhami steel amplifiers together with a rubber tape and implant them into the top clip of a brush of a screen wiper. At the same time short moustaches of a clip have to enter clamps on a rubber tape, see rice. An arrangement of dredging of a clamp on a rubber tape of a brush of a screen wiper.
4. Install screen wiper brushes on levers in the sequence, the return to removal. At the same time the clamp has to record accurately a brush on the screen wiper lever.
5. Lower the screen wiper lever on a windshield.