VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
   + 11.6. Forward cross panel
   11.7. Front bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of the side directing bumper arm
   11:10. Rear bumper
   11:11. Forward wing
   11:12. Facing of a niche of a forward wheel
   11:13. Air inlet lattice
   + 11:14. Cowl
   11:15. Front grille
   + 11:16. Cable of opening of the lock of a cowl
   11:17. Cowl lock
   11:18. Internal finishing of a door
   11:19. Differences at removal of an upholstery of the right forward door
   11:20. Control unit of door mechanisms
   11:21. Consolidation of a door
   11:22. Side finishing of the luggage compartment of the Sedan models
   11:23. Side finishing of the luggage compartment of the Station wagon models
   11:24. Back finishing of the luggage compartment on the Sedan models
   11:25. Trunk lid upholstery
   11:26. Luggage carrier door upholstery
   11:27. A covering of half of the luggage compartment on the Station wagon models
   11:28. Trunk lid
   + 11:29. Luggage carrier lock
   11:30. Adjustment of provision of a cover of a luggage carrier / back door
   + 11:31. The lock of a back door on the Station wagon models
   11:32. Forward door
   11:33. Cylinder of the lock of a forward door
   11:34. External handle of opening of a door
   11:35. Door lock
   11:36. Manual lowering of glass of a door
   11:37. Door glass
   11:38. Door arm
   11:39. Internal rear-view mirror
   11:40. Central console
   11:41. Forward ashtray
   11:42. Back ashtray
   11:43. Decorative overlay of the lever (automatic transmission)
   11:44. Decorative slips under the radio receiver
   11:45. The lower finishing of the dashboard from the driver
   11:46. Ware box
   11:47. Internal decorative overlay of an external rear-view mirror
   11:48. Ceiling handle
   11:49. Antisolar peaks
   11:50. Overlays of thresholds
   11:51. Wind and back flew down
   11:52. Sitting lobbies
   11:53. Head restraint
   11:54. Side safety cushions
   11:55. Back sitting
   11:56. Left back of back sitting
   11:57. Carpet
   11:58. Elements of finishing of an interior
   11:59. External mirror of a back type / glass of a mirror
   11.60. Case of an external mirror
   11.61. Protection / бордюрная roof level
   11.62. Side overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windshield
   11.65. Screen wiper levers
+ 12. Heating, ventilation
+ 13. Electric equipment






11:35. Door lock

GENERAL INFORMATION

The door lock, window regulator and loudspeaker fasten on one arm of a door.

Removal of the lock of a door can be made only together with an arm.

Removal of an arm of a door can be made only after door glass release from window regulator clamps. For this purpose lower door glass to the level of technological openings in an arm and release clamps.

If at doors window regulators with the electric drive are established and they for any reason do not work at present, it is possible to lower door glass manually.

Removal

Use of a dorn for release of clamps (1) of fastening of the lock of a door to an arm

Separation of the lock of a door from an arm

1 – bracket,
2 – cable,
3 – screw-driver,
4 – door lock

Separation of safety draft from the door lock

1 – safety draft,
2 – hummock draft

PERFORMANCE ORDER
1. Remove an upholstery of a forward door.
2. Remove the lock cylinder case.
3. Release a clamp of the external handle of opening of a door.
4. Remove an arm with units from a forward door.
5. Using дорн, release clamps (1) of fastening of the lock of a door, see rice. Use of a dorn for release of clamps (1) of fastening of the lock of a door to an arm.
6. Release from a fixing bracket (1) a cable (2), see rice. Separation of the lock of a door from an arm.
7. Using the screw-driver, separate from a door arm the door lock with a transitional angular arm. Transitional the angular arm fastens to the door lock a bolt and a rivet.
8. Take safety draft (1) from the door lock for what turn the door lock in the direction of the arrow shown on rice. Separation of safety draft from the door lock.
9. Release fastenings of a cover of hummock thirst for the door lock.
10. Turn a tip of hummock draft on 90 ° and take it from an opening in the door lock lever.

Installation

PERFORMANCE ORDER
1. Installation is made in the sequence, the return to removal.
2. Check operation of the lock of a door.