VW Passat B5

since 1996 release

Repair and operation of the car



Foltsvagen Passat B5
+ Maintenance instruction
+ 1. Maintenance
+ 2. Engines
+ 3. Cooling system
+ 4. Fuel system
+ 5. Engine management
+ 6. Exhaust system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.2. Care of a body
   11.3. Care of an upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of strong damages of a body
   + 11.6. Forward cross panel
   11.7. Front bumper
   11.8. Removal of the lever of blocking of a cowl
   11.9. Adjustment of the side directing bumper arm
   11:10. Rear bumper
   11:11. Forward wing
   11:12. Facing of a niche of a forward wheel
   11:13. Air inlet lattice
   + 11:14. Cowl
   11:15. Front grille
   + 11:16. Cable of opening of the lock of a cowl
   11:17. Cowl lock
   11:18. Internal finishing of a door
   11:19. Differences at removal of an upholstery of the right forward door
   11:20. Control unit of door mechanisms
   11:21. Consolidation of a door
   11:22. Side finishing of the luggage compartment of the Sedan models
   11:23. Side finishing of the luggage compartment of the Station wagon models
   11:24. Back finishing of the luggage compartment on the Sedan models
   11:25. Trunk lid upholstery
   11:26. Luggage carrier door upholstery
   11:27. A covering of half of the luggage compartment on the Station wagon models
   11:28. Trunk lid
   + 11:29. Luggage carrier lock
   11:30. Adjustment of provision of a cover of a luggage carrier / back door
   + 11:31. The lock of a back door on the Station wagon models
   11:32. Forward door
   11:33. Cylinder of the lock of a forward door
   11:34. External handle of opening of a door
   11:35. Door lock
   11:36. Manual lowering of glass of a door
   11:37. Door glass
   11:38. Door arm
   11:39. Internal rear-view mirror
   11:40. Central console
   11:41. Forward ashtray
   11:42. Back ashtray
   11:43. Decorative overlay of the lever (automatic transmission)
   11:44. Decorative slips under the radio receiver
   11:45. The lower finishing of the dashboard from the driver
   11:46. Ware box
   11:47. Internal decorative overlay of an external rear-view mirror
   11:48. Ceiling handle
   11:49. Antisolar peaks
   11:50. Overlays of thresholds
   11:51. Wind and back flew down
   11:52. Sitting lobbies
   11:53. Head restraint
   11:54. Side safety cushions
   11:55. Back sitting
   11:56. Left back of back sitting
   11:57. Carpet
   11:58. Elements of finishing of an interior
   11:59. External mirror of a back type / glass of a mirror
   11.60. Case of an external mirror
   11.61. Protection / бордюрная roof level
   11.62. Side overlay of a body
   11.63. Replacement of rubber tapes of brushes of screen wipers
   11.64. Nozzles of washers of a windshield
   11.65. Screen wiper levers
+ 12. Heating, ventilation
+ 13. Electric equipment







11:18. Internal finishing of a door

GENERAL INFORMATION

Arrangement of the electric socket on the internal handle of a door

1 – socket clamp,
2 – electric socket,

Arrow – the direction of a pulling of a clamp of the electric socket.


Removal

Removal of draft of the internal handle of opening of a door

1 – draft,
2 – directing drafts,
3, 4 – electric sockets

The description of removal of internal finishing of a door of the driver is provided in this subsection. Internal finishing of back doors is removed in the same way, as well as lobbies.

PERFORMANCE ORDER
1. Switch off ignition and remove a weight wire from the accumulator.
2. Insert an edge of the thin screw-driver between an overlay of the handle and handle with dredging and move an overlay of the handle to a door. Use the screw-driver with very thin edge not to damage a plastic overlay of the handle and the handle of a door.
3. Using the screw-driver inserted under edge of the handle with dredging take the handle with dredging from internal finishing of a door. Do not remove the internal handle of a door for dredging as under it there is a crossing point of internal finishing of a door.
4. Extend a clamp of the electric socket from the socket and disconnect the electric socket from the internal handle of a door, see rice. An arrangement of the electric socket on the internal handle of a door.
5. Through an opening after removal of the handle of a door unscrew three screws.
6. Unscrew the screws fixing the lower part of internal finishing of a door.
7. Unscrew and remove the button of blocking of the lock of a door.
8. Using special VW-3392 adaptation or the ny tool in the form of a flat fork is independently manufactured, separate a door upholstery from a door.
9. Lifting a door upholstery up, release the top part of an upholstery of a door from a window opening.
10. Moving draft of opening of a door back, take it from a guide and disconnect from the internal handle of opening of a door, see rice. Removal of draft of the internal handle of opening of a door.
11. Remove a door upholstery.
12. Remove the lower internal consolidation of glass from a door upholstery and establish it in a window aperture.

Installation

PERFORMANCE ORDER
1. Before installation of an upholstery of a door check a condition of clamps of an upholstery and, if necessary, replace the damaged clamps. Establish clamps in an opening in a door upholstery.
2. Installation of an upholstery of a door is made in the sequence, the return to removal.
3. Connect a weight wire to the accumulator.